
Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
Foam injection
Foam injection gun steel version / Foam injection gun Teflon version

- Teflon injection gun, equipped with a stainless steel needle and pressure regulation. Allows precise dosing of the product. The polyurethane foam does not adhere to the surface of the gun, providing easy cleaning
- Steel injection gun, equipped with a steel needle and pressure regulation.
- To increase the life of tools, clean them after each use. Dirt from foam can be cleaned with Premium Foam Cleaner or Premium Foam Remover depending on the condition of the dirtiness of the tool.

Product code | EAN code | Needle | Material | Package | Outer cartoon |
- | - | pcs. | pcs. | ||
EP0031 | 4742205004204 | STAINLESS STEEL | TEFLON | 1 | - |
000222 | 5902431721194 | STEEL | STEEL | 1 | - |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
PENOSIL PREMIUM FOAM REMOVER
Professional agent for removing cured polyurethane foam

- Colorless agent
- Manufactured on the basis of solvent, highly toxic.
- Use for removing foam from heavily dirt injection guns, tools and other surfaces
- Before use, test the invisible part of the cleaned surface due to the risk of permanent damage (tarnish, discoloration)
- Before use, shake the can with agent vigorously at least 20 times
- Apply the agent on cured foam using a dosing nozzle, taking care on other surfaces (PREMIUM FOAM REMOVER dissolves varnishes, paints, etc.). The agent should be left for 5-10 minutes and then the softened foam should be removed mechanically. If necessary, clean the surface with PREMIUM CLEANING WIPES
- Exercise extreme caution. The product contains flammable gases
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Quantity / Volume | Application | Foam condition | Version | Package | Outer cartoon |
- | - | - | - | pcs. | pcs. | |||
A1609 | 4742640000465 | CAN | 500ml | INJECTION GUN | CURED | FOAM REMOVER | 1 | 12 |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
PENOSIL PREMIUM FOAM CLEANER
Professional agent for removing uncured polyurethane foam

- Colorless agent
- Manufactured on the basis of acetone, highly toxic.
- Use for removing foam from clothes, tools, foam cans, injection guns immediately after use, and surfaces dirty with uncured foam
- Before use, test the invisible part of the cleaned surface due to the risk of permanent damage (tarnish, discoloration)
- Before use, shake the can with agent vigorously at least 20 times
- Apply the agent on uncured foam using a dosing nozzle, taking care on other surfaces and then remove softened foam
- When cleaning injection gun, place the can with cleaning agent on the injection gun and clean it by pressing the trigger until the foam stops flowing out. The gun shouldn’t be directed towards other people when cleaning
- Exercise extreme caution. The product contains flammable gases
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Quantity / Volume | Application | Foam condition | Version | Package | Outer cartoon |
- | - | - | - | pcs. | pcs. | |||
A1530 | 4742205009841 | CAN | 500ml | INJECTION GUN | UNCURED | FOAM CLEANER | 1 | 12 |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
PENOSIL PREMIUM CLEANING WIPES
Universal wipes for removing dirt from uncured polyurethane foam, silicones, adhesives and paints from various surfaces

- 15,6 x 21,3 cm wipes supplied in a plastic container
- Wipes have a neutral pH. Are friendly to human skin – contain vitamin E and aloe extract.
- Use for removing uncured foam, paint, glue, sealer, etc. from hands, tools and other surfaces
- Before use, test the invisible part of the surface to be cleaned (if it is made of plastic or fabric), due to the risk of discoloration. The test will also show the effectiveness of the use of wipes
- Place the wipe on the uncured foam for a few minutes and then wipe off the stain.
- Always keep the container with wipes tightly closed after use
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Quantity / Volume | Application | Foam condition | Version | Package | Outer cartoon |
- | - | - | - | pcs. | pcs. | |||
EL0011 | 5903111917685 | WIPES | 50pcs. | - | UNCURED | CLEANING WIPES | 1 | 12 |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
NEUTRAL SILICONE OLIVE C-22
Neutral silicone with a low modulus of elasticity for sealing gaps between porous and non-porous substrates

- One-component high quality silicone sealant with a low elasticity, naturally cured, supplied in cartouches or plastic packaging
- White/colorless color
- Adheres well to many building materials without primer, except: Teflon, polyethylene and polypropylene surfaces
- Characterize by high resistance to UV radiation, weather conditions and aging.
- The surface on which the application is made must be free of dust, dirt and oil
- Non-porous surfaces such as aluminum or glass should be cleaned with a suitable solvent
- Porous surfaces, such as concrete or brick, should be mechanically cleaned
- It is recommended to use primer for better grip. An adhesion test is recommended each time
- After surface preparation, the silicone is applied using a suitable injection gun. The joints should be processed and smoothed before forming the epidermis
- For the deep gaps, the possibility of moving the silicone should be considered
- The silicone can’t be painted
- Uncured silicone can be removed with solvents such as isopropyl alcohol or mineral spirits
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Volume | Application | Expiry date | Color | Single box | Outer cartoon |
ml | - | months | - | pcs. | pcs. | |||
12021412G04F04 | 5903111917777 | FOIL TUBE | 600 | FOIL TUBE EXTRUDER | 12 | WHITE | 1 | 20 |
OLI000159 | - | CARTOUCHE | 300 | INJECTION GUN | 12 | WHITE | 1 | 24 |
12021412G04T30 | 5903111917784 | FOIL TUBE | 600 | FOIL TUBE EXTRUDER | 12 | COLORLESS | 1 | 20 |
12023411C03T01 | 5902431720395 | CARTOUCHE | 300 | INJECTION GUN | 12 | COLORLESS | 1 | 24 |
Properties | Unit | Value |
Tack free time | minute | 5-10 |
Curing time | mm/24h | about 3 |
Dead weight | g/ml | about 1 |
Resistance to flow (ISO 7390 ) | mm | about 0 |
Application temperature | °C | from +5 to +40 |
Working temperature | °C | from -40 to +150 |
Hardness (Shore A) (ISO 868 ) | - | about 18 |
TENSILE STRENGTH: | ||
Joint 12x12x50 mm – ISO 8339 | ||
Modulus of elasticity at 100% elongation (ISO 8339 ) | Mpa | about 0,35 |
Tensile strength (ISO 8339 ) | Mpa | about 1,30 |
Elongation at break (ISO 8339 ) | % | >550 |
The following values were obtained at temperature +23°C and 50% relative humidity, unless stated otherwise. |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
BEST & PROF PU 40 HM
High quality one-component polyurethane adhesive-sealer for non-structural use in joints in buildings

- One-component polyurethane adhesive-sealer, supplied in plastic packaging
- Grey/White color
- Adheres well to many building materials. Resistant to water, cleaning agents, oils, acids and diluted bases
- For insulation and sealing inside and outside
- Cured sealer is resistant to moisture, UV radiation and weather conditions
- Class E reaction to fire acc. PN-EN 13501-1+A1:2010.
- The surfaces on which the application is made must be clean, dry, free from water and dirt, oil, grease or rust
- Glass, metal and other non-porous surfaces must be free of painting layer and cleaned with a solvent
- Adhesive-sealer should be applied using suitable injection gun by smoothly moving the nozzle along the gap. Steady application prevents formation of air bubbles
- Wide gaps should be filled in two steps, by pre-covering both walls of the gap, and then filling the middle part of the gap
- Completely cured adhesive-sealer can be painted with dispersion paints
- Uncured adhesive-sealant can be removed with crude oil. Cured can only be removed mechanically. Hands can be cleaned with Premium Cleaning Wipes
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Color | Kind | Volume | Application | Expiry date | Package | Outer cartoon |
- | ml | - | months | pcs. | pcs. | |||
0316403209 | - | GREY | FOIL TUBE | 600 | FOIL TUBE EXTRUDER | 12 | 1 | 20 |
0316303209 | - | WHITE | FOIL TUBE | 600 | FOIL TUBE EXTRUDER | 12 | 1 | 20 |
Properties | Unit | Value |
Tack free time | minute | 70 |
Curing time | mm/24h | ≥3 |
Density | g/cm3 | black : 1.15 ± 0.02 ; other : 1.16 ± 0.02 |
The properties of the cured sealant | ||
Modulus of elasticity at 100% elongation (ISO 8339 ) | MPa | 0,40 |
Tensile strength (ISO 8339 ) | MPa | 0,60 |
Recovery of flexibility (ISO 8339 ) | % | >70 |
Elongation at break (ISO 8339 ) | % | >500 |
Movement in the slot | % | 25 |
Hardness (Shore A) (ISO 868 ) | - | about 40 |
Thermal resistance after curing | °C | from -40 to +80 |
Resistance to salt water | - | Perfect |
Resistance to UV radiation | - | Good |
Resistance to dilute acids and bases | - | Medium |
The following values were obtained at temperature +23°C and 50% relative humidity, unless stated otherwise. |
Connected products. Do not forget about accessories!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL PREMIUM FIRERATED GUNFOAM B1
Professional, firestop pistol foam for filling gaps

- One-component professional fire-resistant foam with a structure of 70% / 30% (closed cells / open cells) and low expansion, supplied in cans with aerosol
- Light pink color
- Available in summer version
- Adheres well to many building materials, except: Teflon, polyethylene and silicone surfaces
- Provides very good sound and thermal insulation
- Class B-s1, d0 reaction to fire acc. PN-EN 13501-1+A1:2010.
- The surface on which the application is made must be free of dust, dirt and oil
- The surface on which the application will be made should be well moistened. Lack of adequate humidity can cause secondary expansion
- Used for gaps or linear joints up to 50 mm wide
- Applied on substrates of at least A2 reaction to fire
- When applying in low temperatures, the can with foam should be preheated in a warm place or water. Place or water temperature should not exceed + 30 ° C
- Before use, shake the can with foam vigorously at least 20 times
- The amount of foam discharged should be adjusted with use of the injection gun trigger.
- After curing, the foam is not UV-resistant and must be covered within 24 hours. Unprotected foam gets brittle. The foam can be painted with water-based paints
- Dirt from foam can be cleaned with Premium Foam Cleaner, Premium Foam Remover or with Premium Cleaning Wipes. Details are given in the cards of these products
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Working temperature | Volume | Application | Expiry date | Version | Package | Outer cartoon | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | months | - | pcs. | pcs. | ||
A1592 | 4742640006948 | CAN WITH FOAM | +5 | +30 | 750 | INJECTION GUN | 12 | FIRESTOP | 1 | 12 |
Properties | Unit | Value |
Tack free time | minute | 12-16 |
Cutting time (30 mm strap) | minute | 30-40 |
Cutting time (30 mm strap)°C) | hour | up to 18 |
Completely cured in joint (in temperature +5 °C) | hour | up to 24 |
Density | kg/m3 | 25-30 |
Fire-resistance of cured foam (PN-EN 13501-2:2010 ) | EI15 - EI120 | |
Fire class of cured foam (PN-EN 13501-1+A1:2010 ) | - | B-s1,d0 |
Volume decrease | % | non |
Post-expansion | % | up to 30 |
Flash point of cured foam | °C | 400 |
Tensile strength (BS 5241 ) | N/cm2 | 8 |
Compression strength at 10% deformation (DIN 53421 ) | N/cm2 | 2,5 |
Thermal conductivity | W/m*K | 0,034 |
Temperature resistance of cured foam | °C | long period: -50 to +90 |
The following values were obtained at temperature +23°C and 50% relative humidity, unless stated otherwise. |
Joint depth | mm | ≥100 | ≥100 | ≥100 | ≥100 | ≥200 | ≥200 | ≥200 | ≥200 |
Joint width | mm | ≤40 | ≤30 | ≤20 | ≤10 | ≤40 | ≤30 | ≤20 | ≤10 |
EI | min | 45 | 45 | 60 | 60 | 120 | 120 | 150 | 180 |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
PENOSIL REMONT
Low-pressure, standard performance pistol foam for filling gaps

- One-component standard performance polyurethane foam, supplied in cans with aerosol
- Light yellow color
- Available in winter and summer versions
- Adheres well to many building materials, except: Teflon, polyethylene and silicone surfaces
- Provides very good sound and thermal insulation
- Class F reaction to fire acc. PN-EN 13501-1+A1:2010.
- The surface on which the application is made must be free of dust, dirt and oil
- The surface on which the application will be made should be well moistened. Lack of adequate humidity can cause secondary expansion
- When applying in low temperatures, the can with winter foam version should be preheated in a warm place or water. Place or water temperature should not exceed + 30 ° C
- Before use, shake the can with foam vigorously at least 20 times
- The amount of foam discharged should be adjusted with use of the injection gun trigger.
- After curing, the foam is not UV-resistant and must be covered within 24 hours. Unprotected foam gets brittle. The foam can be painted with water-based paints
- Dirt from foam can be cleaned with Premium Foam Cleaner, Premium Foam Remover or with Premium Cleaning Wipes. Details are given in the cards of these products
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Working temperature | Volume | Application | Expiry date | Version | Package | Outer cartoon | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | months | - | pcs. | pcs. | ||
A4594 | - | CAN WITH FOAM | +5 | +30 | 750 | INJECTION GUN | 12 | SUMMER | 1 | 12 |
A4608 | - | CAN WITH FOAM | -5 | +30 | 750 | INJECTION GUN | 12 | WINTER | 1 | 12 |
Properties | Unit | Value |
Tack free time | minute | 10-14 |
Cutting time (30 mm strap) | minute | 35-45 |
Completely cured in joint (in temperature +23 °C) | hour | up to 18 |
Completely cured in joint (in temperature +5 °C) | hour | up to 24 |
Density | kg/m3 | 20-25 |
Fire class of cured foam (PN-EN 13501-1+A1:2010 ) | - | F |
Volume decrease | % | non |
Post-expansion | % | up to 30 |
Flash point of cured foam | °C | 400 |
Tensile strength (BS 5241 ) | N/cm2 | 10 |
Compression strength at 10% deformation (DIN 53421 ) | N/cm2 | 4 |
Thermal conductivity | W/m*K | 0,034 |
Sound reduction index | dB | RST,w = 60 |
Temperature resistance of cured foam | °C | long period: -50 to +90 short period: -65 to +130 |
The following values were obtained at temperature +23°C and 50% relative humidity, unless stated otherwise. |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
PENOSIL PREMIUM GUNFOAM 65
Low-pressure, increased performance pistol foam for filling gaps

- One-component increased performance polyurethane foam with homogeneous structure and low expansion, supplied in cans with aerosol
- Light yellow color
- Available in winter and summer versions
- Adheres well to many building materials, except: Teflon, polyethylene and silicone surfaces
- Provides very good sound and thermal insulation
- Increased efficiency by 15% compared to standard can volume foam
- Class F reaction to fire acc. PN-EN 13501-1+A1:2010.
- The surface on which the application is made must be free of dust, dirt and oil
- The surface on which the application will be made should be well moistened. Lack of adequate humidity can cause secondary expansion
- When applying in low temperatures, the can with winter foam version should be preheated in a warm place or water. Place or water temperature should not exceed + 30 ° C
- Before use, shake the can with foam vigorously at least 20 times
- The amount of foam discharged should be adjusted with use of the injection gun trigger.
- After curing, the foam is not UV-resistant and must be covered within 24 hours. Unprotected foam gets brittle. The foam can be painted with water-based paints
- Dirt from foam can be cleaned with Premium Foam Cleaner, Premium Foam Remover or with Premium Cleaning Wipes. Details are given in the cards of these products
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Working temperature | Volume | Application | Expiry date | Version | Package | Outer cartoon | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | months | - | pcs. | pcs. | ||
A1493 | 4742205009681 | CAN WITH FOAM | +5 | +30 | 900 | INJECTION GUN | 18 | SUMMER | 1 | 12 |
A1540 | 4742640000793 | CAN WITH FOAM | -10 | +30 | 900 | INJECTION GUN | 18 | WINTER | 1 | 12 |
Properties | Unit | Value |
Tack free time | minute | 10-12 |
Cutting time (30 mm strap) | minute | 30-35 |
Completely cured in joint (in temperature +23 °C) | hour | up to 12 |
Completely cured in joint (in temperature +5 °C) | hour | up to 20 |
Density | kg/m3 | 20-25 |
Fire class of cured foam (PN-EN 13501-1+A1:2010 ) | - | F |
Volume decrease | % | non |
Post-expansion | % | up to 33 |
Flash point of cured foam | °C | 400 |
Tensile strength (BS 5241 ) | N/cm2 | 9 |
Compression strength at 10% deformation (DIN 53421 ) | N/cm2 | 3 |
Thermal conductivity | W/m*K | 0,034 |
Sound reduction index | dB | RST,w = 60 |
Temperature resistance of cured foam | °C | long period: -50 to +90 short period: -65 to +130 |
The following values were obtained at temperature +23°C and 50% relative humidity, unless stated otherwise. |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
PENOSIL GOLDGUN 65 PLUS
Low-pressure, high performance pistol foam for filling gaps

- One-component high performance polyurethane foam with homogeneous very light structure and low expansion, supplied in cans with aerosol
- Light yellow color
- Available in the all-season version
- Adheres well to many building materials, except: Teflon, polyethylene and silicone surfaces
- Provides very good sound and thermal insulation. Resistant to moisture and mold
- Increased efficiency by 30% compared to standard can volume foam
- Class F reaction to fire acc. PN-EN 13501-1+A1:2010.
- The surface on which the application is made must be free of dust, dirt and oil
- The surface on which the application will be made should be well moistened. Lack of adequate humidity can cause secondary expansion
- When applying in low temperatures, the can with foam should be preheated in a warm place or water. Place or water temperature should not exceed + 30 ° C
- Before use, shake the can with foam vigorously at least 20 times
- The amount of foam discharged should be adjusted with use of the injection gun trigger.
- After curing, the foam is not UV-resistant and must be covered within 24 hours. Unprotected foam gets brittle. The foam can be painted with water-based paints
- Dirt from foam can be cleaned with Premium Foam Cleaner, Premium Foam Remover or with Premium Cleaning Wipes. Details are given in the cards of these products
- Detailed information on storage, transport and safety are available in the safety data sheet (SDS).

Product code | EAN code | Kind | Working temperature | Volume | Application | Expiry date | Version | Package | Outer cartoon | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | months | - | pcs. | pcs. | ||
A3348 | 4742640008171 | CAN WITH FOAM | -20 | +30 | 850 | INJECTION GUN | 18 | ALL SEASON | 1 | 12 |
Properties | Unit | Value |
Tack free time | minute | 8-10 |
Cutting time (30 mm strap) | minute | 25-30 |
Completely cured in joint (in temperature +23 °C) | hour | up to 12 |
Completely cured in joint (in temperature +5°C) | hour | up to 18 |
Density | kg/m3 | 17-20 |
Fire class of cured foam (PN-EN 13501-1+A1:2010 ) | - | F |
Volume decrease | % | non |
Post-expansion | % | up to 30 |
Flash point of cured foam | °C | 400 |
Tensile strength (BS 5241 ) | N/cm2 | 8 |
Compression strength at 10% deformation (DIN 53421 ) | N/cm2 | 2,5 |
Thermal conductivity | W/m*K | 0,034 |
Sound reduction index | dB | RST,w = 60 |
Temperature resistance of cured foam | °C | long period: -50 do +90 short period: -65 do +130 |
The following values were obtained at temperature +23°C and 50% relative humidity, unless stated otherwise. |
Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Program Eurofast
We invite you to get acquainted with a wide range of offered products










Technical service
Cooperating with Eurofast, Customers get comprehensive technical support
CAD Blocks
Files to Download
Fixing Plans
Technical Support
Operator Manuals
Approvals and Certificates
Documentation of offered products can be downloaded directly from our website
Partners Eurofast Poland
Market presence allowed us to develop mutually beneficial relationships with many companies in Poland and Europe
Realizations
Our quality is our realizations. Check that we don’t throw words to the wind
Region: Łódź
Construction company: Megamont
Used screws:
- M5
- M6S-P
- M12S-P
Region: Łódź
Construction company: Ocmer Sp. z o. o.
Used screws:
- M0
- M5
- M12
- M6S-P
- M12S-P
Region: Łódź
Construction company: Ocmer Sp. z o. o.
Used screws:
- M6S-P
- M12S-P
- MW-2
Eurofast Poland in the media
Our publications in professional journals
About Eurofast Poland


Eurofast Poland (formerly known as Baltic Fasteners) consists of specialists with experience in the fasteners market.
Our team is professional and competent with experience supported by the knowledge required to perform tasks adequately. Attitude of the team is searching for new solutions in various sectors of the market.
Our specialists carry out the whole process of implementation: examine customer expectations, develop and test new products. Our work is challenging, requiring extensive knowledge in many areas.
The added value is the great atmoshphere of the team, ensuring the harmony of cooperation and a high quality of service.
Our team
Meet our team
Show number
Show e-mail
Polski / Pусский

Show number
Show e-mail
Polski

Show number
Show e-mail
Polski / English

Show number
Show e-mail
Polski / English

Show number
Show e-mail
Polski / English

Show number
Show e-mail
Polski / English

Show number
Show e-mail
Polski

Diversity is only limited by imagination
Pistolet do piany
Pistolet do piany wersja stalowa/ Pistolet do piany wersja teflonowa

- Teflonowy pistolet do piany montażowej, wyposażony w igłę z stali nierdzewnej oraz regulację ciśnienia. Pozwala na dokładne dozowanie produktu. Piana poliuretanowa nie przywiera do powierzchni pistoletu, zapewniając możliwość łatwego czyszczenia
- Stalowy pistolet do piany montażowej, wyposażony w igłę z stali oraz regulację ciśnienia.
- W celu zwiększenia żywotności narzędzi, należy je czyścić po każdym użyciu. Pozostałości piany można oczyścić przy pomocy produktów Premium Foam Cleaner lub Premium Foam Remover w zależności od stanu zabrudzenia narzędzia.

Kod produktu | Numer EAN | Igła | Materiał | Opakowanie | Karton zbiorczy |
- | - | szt. | szt. | ||
EP0031 | 4742205004204 | NIERDZEWNA | TEFLONOWY | 1 | - |
000222 | 5902431721194 | STALOWA | STALOWY | 1 | - |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL PREMIUM FOAM REMOVER
Profesjonalny środek do usuwania utwardzonej piany poliuretanowej

- Środek bezbarwny
- Wyprodukowany na bazie rozpuszczalnika, silnie toksyczny.
- Stosować do usuwania piany z mocno zabrudzonych pistoletów, narzędzi i innych powierzchni
- Przed użyciem należy przeprowadzić test na niewidocznej części czyszczonej powierzchni ze względu na ryzyko trwałego jej uszkodzenia (zmatowienie, odbarwienie)
- Przed użyciem należy wstrząsnąć energicznie pojemnik ze środkiem czyszczącym przynajmniej 20 razy
- Środek należy nanieść na utwardzoną pianę przy pomocy dyszy dozującej, uważając na sąsiadujące powierzchnie (PREMIUM FOAM REMOVER rozpuszcza lakiery, farby itp.). Środek należy pozostawić na 5-10 minut, a następnie usunąć zmiękczoną pianę mechanicznie. Jeśli to konieczne powierzchnię należy doczyścić przy pomocy PREMIUM CLEANING WIPES
- Należy zachować szczególną ostrożność przy pracy. Środek zawiera łatwopalne gazy
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Ilość /Objętość | Sposób aplikacji | Stan piany | Wersja | Opakowanie | Karton zbiorczy |
- | - | - | - | szt. | szt. | |||
A1609 | 4742640000465 | POJEMNIK | 500ml | PISTOLET | Utwardzona | FOAM REMOVER | 1 | 12 |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL PREMIUM FOAM CLEANER
Profesjonalny środek do usuwania nieutwardzonej piany poliuretanowej

- Środek bezbarwny
- Wyprodukowany na bazie acetonu.
- Stosować do usuwania piany z ubrań, narzędzi, zaworów pian w puszkach, pistoletów zaraz po ich użyciu oraz powierzchni zabrudzonych nieutwardzoną pianą
- Przed użyciem należy przeprowadzić test na niewidocznej części czyszczonej powierzchni ze względu na ryzyko trwałego jej uszkodzenia (zmatowienie, odbarwienie)
- Przed użyciem należy wstrząsnąć energicznie pojemnik ze środkiem czyszczącym przynajmniej 20 razy
- Środek należy nanieść na nieutwardzoną pianę przy pomocy dyszy dozującej, uważając na sąsiadujące powierzchnie, a następnie usunąć zmiękczoną piankę
- W przypadku czyszczenia pistoletu do pian, umieść podłącz pojemnik ze środkiem czyszczącym do pistoletu a następnie oczyść go naciskając spust, aż do momentu, gdy piana przestanie wypływać. Podczas czyszczenia pistoletu nie należy kierować w stronę innych osób
- Należy zachować szczególną ostrożność przy pracy. Środek zawiera łatwopalne gazy
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Ilość /Objętość | Sposób aplikacji | Stan piany | Wersja | Opakowanie | Karton zbiorczy |
- | - | - | - | szt. | szt. | |||
A1530 | 4742205009841 | POJEMNIK | 500ml | PISTOLET | Nieutwardzona | FOAM CLEANER | 1 | 12 |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL PREMIUM CLEANING WIPES
Uniwersalne ściereczki do usuwania zabrudzeń z nieutwardzonej piany poliuretanowej, silikonów, klejów i farb z różnych powierzchni

- Chusteczki o wymiarach 15,6 x 21,3cm dostarczane w plastikowym pojemniku
- Mają neutralne pH. Są przyjazne dla ludzkiej skóry – zawierają witaminę E i wyciąg z aloesu.
- Stosować do usuwania nieutwardzonej piany, farby, kleju, uszczelniacza itp. z dłoni, narzędzi i innych powierzchni
- Przed użyciem należy przeprowadzić test na niewidocznej części czyszczonej powierzchni, jeżeli jest ona wykonana z tworzywa sztucznego lub tkaniny, ze względu na ryzyko odbarwienia. Test wykaże również skuteczność użycia chusteczek
- Chusteczkę należy umieścić na plamie z nieutwardzonej piany na kilka minut, a następnie zetrzeć plamę
- Pojemnik z chusteczkami należy zawsze szczelnie zamknąć po użyciu
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Ilość /Objętość | Sposób aplikacji | Stan piany | Wersja | Opakowanie | Karton zbiorczy |
- | - | - | - | szt. | szt. | |||
EL0011 | 5903111917685 | ŚCIERECZKI | 50szt. | - | Nieutwardzona | CLEANING WIPES | 1 | 12 |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
SILIKON NEUTRALNY OLIVE C-22
Silikon neutralny o niskim module sprężystości do uszczelniania szczelin między porowatymi i nieporowatymi podłożami

- Jednoskładnikowy wysokiej klasy uszczelniacz silikonowy o niskim module sprężystości, naturalnie utwardzany, dostarczany w kartuszach lub opakowaniach foliowych
- Silikon w kolorze białym / bezbarwnym
- Dobrze przylega do większości materiałów budowlanych bez gruntowania, z wyjątkiem powierzchni z Teflonu, polietylenu i polipropylenu
- Charakteryzuje się wysoką odpornością na promieniowanie UV, warunki atmosferyczne oraz starzenie się.
- Powierzchnia, na którą wykonywana jest aplikacja musi być wolna od kurzu, luźnych cząstek i oleju
- Powierzchnie nieporowate takie jak aluminium czy szkło, powinny być wyczyszczone odpowiednim rozpuszczalnikiem
- Powierzchnie porowate takie jak beton czy cegła, powinny być oczyszczone mechanicznie
- W celu uzyskania lepszej przyczepności zaleca się użycie gruntu. Każdorazowo zaleca się wykonanie testu przyczepności
- Po przygotowaniu powierzchni, silikon aplikuje się przy pomocy odpowiedniego wyciskacza. Szczeliny powinny być obrobione i wygładzone przed uformowaniem naskórka
- Przy głębokich szczelinach należy uwzględnić możliwość przemieszczania silikonu
- Silikon nie może być malowany
- Nieutwardzony silikon można usunąć przy pomocy rozpuszczalników takich jak alkohol izopropylowy lub spirytus mineralny
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Objętość | Sposób aplikacji | Termin przydatności | Kolor | Opakowanie | Karton zbiorczy |
ml | - | miesiące | - | szt. | szt. | |||
12021412G04F04 | 5903111917777 | TUBA FOLIOWA | 600 | WYCISKACZ DO TUB FOLIOWYCH | 12 | BIAŁY | 1 | 20 |
OLI000159 | - | KARTUSZ | 300 | WYCISKACZ RĘCZNY | 12 | BIAŁY | 1 | 24 |
12021412G04T30 | 5903111917784 | TUBA FOLIOWA | 600 | WYCISKACZ DO TUB FOLIOWYCH | 12 | BEZBARWNY | 1 | 20 |
12023411C03T01 | 5902431720395 | KARTUSZ | 300 | WYCISKACZ RĘCZNY | 12 | BEZBARWNY | 1 | 24 |
Właściwości | Jednostka | Wartość |
Czas formowania naskórka | minuta | 5-10 |
Czas utwardzania | mm/24h | około 3 |
Ciężar własny | g/ml | około 1 |
Odporność na spływanie (ISO 7390 ) | mm | około 0 |
Temperatura aplikacji | °C | od +5 do +40 |
Temperatura pracy | °C | od -40 do +150 |
Twardość (Shore A) (ISO 868 ) | - | około 18 |
WYTRZYMAŁOŚĆ NA ROZCIĄGANIE: | ||
Spoina 12x12x50 mm - ISO 8339 | ||
Moduł sprężystości przy 100% wydłużeniu (ISO 8339 ) | Mpa | około 0,35 |
Wytrzymałośc na rozciąganie (ISO 8339 ) | Mpa | około 1,30 |
Wydłużenie przy zerwaniu (ISO 8339 ) | % | >550 |
Podane powyżej wartości uzyskano w temperaturze +23°C i przy względnej wilgotności 50%, chyba że podano inaczej. |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
BEST & PROF PU 40 HM
Wysokiej jakości jednoskładnikowy klej-uszczelniacz poliuretanowy do połączeń niestrukturalnych w budynkach

- Jednoskładnikowy klej-uszczelniacz poliuretanowy, dostarczany w opakowaniach foliowych
- Klej-uszczelniacz w kolorze szarym/białym
- Dobrze przylega do większości materiałów budowlanych. Odporny na wodę, środki czyszczące, oleje, kwasy i rozcieńczone zasady
- Do izolacji i uszczelniania wewnątrz i na zewnątrz
- Utwardzony uszczelniacz jest odporny na wilgoć, promieniowanie UV i warunki atmosferyczne
- Klasa E reakcja na ogień wg. PN-EN 13501-1+A1:2010.
- Powierzchnie, na które wykonywana jest aplikacja muszą być czyste, suche, wolne od wody i luźnych cząstek, oleju, smaru lub rdzy
- Szkło, metal i inne powierzchnie nieporowate w miejscu aplikacji muszą być pozbawione powłoki lakierniczej i oczyszczone za pomocą rozpuszczalnika
- Klej-uszczelniacz należy aplikować przy pomocy odpowiedniego wyciskacza, przeciągając płynnie dyszę wzdłuż szczeliny. Równomierna aplikacja zapobiega powstawaniu pęcherzyków powietrza
- Szerokie szczeliny powinny być wypełniane w dwóch etapach, poprzez wstępne pokrycie obu ścian szczeliny, a następnie wypełnienie środkowej części szczeliny
- Całkowicie utwardzony klej-uszczelniacz może być malowany farbami dyspersyjnymi
- Nieutwardzony klej-uszczelniacz można usunąć za pomocą ropy naftowej. Utwardzony, można usunąć wyłącznie mechanicznie. Dłonie można oczyścić przy pomocy chusteczek Premium Cleaning Wipes
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Kolor | Postać | Objętość | Sposób aplikacji | Termin przydatności | Opakowanie | Karton zbiorczy |
- | ml | - | miesiące | szt. | szt. | |||
0316403209 | - | SZARY | TUBA FOLIOWA | 600 | WYCISKACZ DO TUB FOLIOWYCH | 12 | 1 | 20 |
0316303209 | - | BIAŁY | TUBA FOLIOWA | 600 | WYCISKACZ DO TUB FOLIOWYCH | 12 | 1 | 20 |
Właściwości | Jednostka | Wartość |
Czas formowania naskórka | minuta | 70 |
Czas utwardzania | mm/24h | ≥3 |
Gęstość | g/cm3 | czarny : 1.15 ± 0.02 ; inny : 1.16 ± 0.02 |
Właściwości utwardzonego uszczelniacza | ||
Moduł sprężystości przy 100% wydłużeniu (ISO 8339 ) | MPa | 0,40 |
Wytrzymałość na rozciąganie (ISO 8339 ) | MPa | 0,60 |
Odzysk elastyczności (ISO 8339 ) | % | >70 |
Wydłużenie przy zerwaniu (ISO 8339 ) | % | >500 |
Ruch w szczelinie | % | 25 |
Twardość (Shore A) (ISO 868 ) | - | około 40 |
Odporność termiczna po utwardzeniu | °C | od -40 do +80 |
Odporność na słoną wodę | - | Doskonała |
Odporność na promieniowanie UV | - | Dobra |
Odporność na rozcieńczone kwasy i zasady | - | Średnia |
Podane powyżej wartości uzyskano w temperaturze +23°C i przy względnej wilgotności 50%, chyba że podano inaczej. |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL PREMIUM FIRERATED GUNFOAM B1
Profesjonalna ogniochronna piana pistoletowa do wypełniania szczelin

- Jednoskładnikowa profesjonalna piana ogniochronna o strukturze 70%/30% (komórek zamkniętych / komórek otwartych) i niskiej ekspansji wtórnej, dostarczana w puszkach z aerozolem
- Piana w kolorze jasnoróżowym
- Piana występuje w wersji letniej
- Dobrze przylega do większości materiałów budowlanych, z wyjątkiem teflonu, polietylenu i powierzchni silikonowych
- Zapewnia bardzo dobrą izolację dźwiękową i cieplną
- Klasa B-s1, d0 reakcja na ogień wg. PN-EN 13501-1+A1:2010.
- Powierzchnia, na którą wykonywana jest aplikacja musi być wolna od kurzu, luźnych cząstek i oleju
- Powierzchnia, na którą wykonujemy aplikację, powinna być dobrze zwilżona. Brak odpowiedniej wilgotności może wywołać wtórne rozprężanie
- Stosowana do szczelin lub złączy liniowych o szerokości do 50 mm
- Stosowana na podłożach co najmniej klasy A2 reakcji na ogień
- Przy aplikacji w niskich temperaturach pojemnik z pianą należy podgrzać przed rozpoczęciem pracy w ciepłym pomieszczeniu lub wodzie. Temperatura pomieszczenia lub wody nie powinna przekraczać +30°C
- Przed aplikacją należy wstrząsnąć energicznie pojemnik z pianą przynajmniej 20 razy
- Ilość wypływającej piany należy regulować za pomocą spustu pistoletu
- Po utwardzeniu piana nie jest odporna na promieniowanie UV i musi zostać zakryta w ciągu 24h. Niezabezpieczona piana robi się krucha. Piana może być malowana farbami na bazie wody
- Pozostałości piany można oczyścić przy pomocy produktów Premium Foam Cleaner, Premium Foam Remover lub przy pomocy chusteczek Premium Cleaning Wipes. Szczegóły podano w kartach tych produktów
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Temperatura pracy | Objętość | Sposób aplikacji | Termin przydatności | Wersja | Pudełko | Karton zbiorczy | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | miesiące | - | szt. | szt. | ||
A1592 | 4742640006948 | POJEMNIK | +5 | +30 | 750 | PISTOLET | 12 | OGNIOCHRONNA | 1 | 12 |
Właściwości | Jednostka | Wartość |
Czas formowania naskórka | minuta | 12-16 |
Czas ścinania (30 mm pasek) | minuta | 30-40 |
Całkowite utwardzenie w szczelinie (w temp. +23 °C) | godzina | do 18 |
Całkowite utwardzenie w szczelinie (w temp. +5 °C) | godzina | do 24 |
Gęstość | kg/m3 | 25-30 |
Klasa odporności ogniowej utwardzonej pianki (PN-EN 13501-2:2010 ) | EI15 - EI120 | |
Klasa reakcji na ogień utwardzonej pianki (PN-EN 13501-1+A1:2010 ) | - | B-s1,d0 |
Zmniejszona objętość | % | brak |
Ekspansja wtórna | % | do 30 |
Temperatura zapłonu utwardzonej pianki | °C | 400 |
Wytrzymałość na rozciąganie (BS 5241 ) | N/cm2 | 8 |
Wytrzymałość na ściskanie przy 10% odkształceniu (DIN 53421 ) | N/cm2 | 2,5 |
Przewodność cieplna | W/m*K | 0,034 |
Wskaźnik izolacyjności akustycznej | dB | RST,w = 60 |
Odporność termiczna po utwardzeniu | °C | długi okres: -50 do +90 krótki okres: -65 do +130 |
Podane powyżej wartości uzyskano w temperaturze +23°C i przy względnej wilgotności 50%, chyba że podano inaczej. |
Głębokość złącza | mm | ≥100 | ≥100 | ≥100 | ≥100 | ≥200 | ≥200 | ≥200 | ≥200 |
Szerokość złącza | mm | ≤40 | ≤30 | ≤20 | ≤10 | ≤40 | ≤30 | ≤20 | ≤10 |
EI | min | 45 | 45 | 60 | 60 | 120 | 120 | 150 | 180 |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL REMONT
Niskoprężna piana pistoletowa o standardowej wydajności do wypełniania szczelin

- Jednoskładnikowa piana poliuretanowa, dostarczana w puszkach z aerozolem
- Piana w kolorze jasnożółtym
- Piana występuje w wersji zimowej i letniej
- Dobrze przylega do większości materiałów budowlanych, z wyjątkiem teflonu, polietylenu i powierzchni silikonowych
- Zapewnia dobrą izolację dźwiękową i cieplną
- Klasa F reakcja na ogień wg. PN-EN 13501-1+A1:2010.
- Powierzchnia, na którą wykonywana jest aplikacja musi być wolna od kurzu, luźnych cząstek i oleju
- Powierzchnia, na którą wykonujemy aplikację, powinna być dobrze zwilżona. Brak odpowiedniej wilgotności może wywołać wtórne rozprężanie
- Przy aplikacji w niskich temperaturach pojemnik z pianą zimową należy podgrzać przed rozpoczęciem pracy w ciepłym pomieszczeniu lub wodzie. Temperatura pomieszczenia lub wody nie powinna przekraczać +30°C
- Przed aplikacją należy wstrząsnąć energicznie pojemnik z pianą przynajmniej 20 razy
- Ilość wypływającej piany należy regulować za pomocą spustu pistolet
- Po utwardzeniu piana nie jest odporna na promieniowanie UV i musi zostać zakryta w ciągu 24h. Niezabezpieczona piana robi się krucha. Piana może być malowana farbami na bazie wody
- Pozostałości piany można oczyścić przy pomocy produktów Premium Foam Cleaner, Premium Foam Remover lub przy pomocy chusteczek Premium Cleaning Wipes. Szczegóły podano w kartach tych produktów
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Temperatura pracy | Objętość | Sposób aplikacji | Termin przydatności | Wersja | Opakowanie | Karton zbiorczy | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | miesiące | - | szt. | szt. | ||
A4594 | - | POJEMNIK | +5 | +30 | 750 | PISTOLET | 12 | LETNIA | 1 | 12 |
A4608 | - | POJEMNIK | -5 | +30 | 750 | PISTOLET | 12 | ZIMOWA | 1 | 12 |
Właściwości | Jednostka | Wartość |
Czas formowania naskórka | minuta | 10-14 |
Czas ścinania (30 mm pasek) | minuta | 35-45 |
Całkowite utwardzenie w szczelinie (w temp. +23 °C) | godzina | do 18 |
Całkowite utwardzenie w szczelinie (w temp. +5 °C) | godzina | do 24 |
Gęstość | kg/m3 | 20-25 |
Klasa reakcji na ogień utwardzonej pianki (PN-EN 13501-1+A1:2010 ) | - | F |
Zmniejszona objętość | % | brak |
Ekspansja wtórna | % | do 30 |
Temperatura zapłonu utwardzonej pianki | °C | 400 |
Wytrzymałość na rozciąganie (BS 5241 ) | N/cm2 | 10 |
Wytrzymałość na ściskanie przy 10% odkształceniu (DIN 53421 ) | N/cm2 | 4 |
Przewodność cieplna | W/m*K | 0,034 |
Wskaźnik izolacyjności akustycznej | dB | RST,w = 60 |
Odporność termiczna po utwardzeniu | °C | długi okres: -50 do +90 krótki okres: -65 do +130 |
Podane powyżej wartości uzyskano w temperaturze +23°C i przy względnej wilgotności 50%, chyba że podano inaczej. |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL PREMIUM GUNFOAM 65
Niskoprężna piana pistoletowa o podwyższonej wydajności do wypełniania szczelin

- Jednoskładnikowa piana poliuretanowa o podwyższonej wydajności, jednorodnej strukturze i niskiej ekspansji wtórnej, dostarczana w puszkach z aerozolem
- Piana w kolorze jasnożółtym
- Piana występuje w wersji zimowej i letniej
- Dobrze przylega do większości materiałów budowlanych, z wyjątkiem teflonu, polietylenu i powierzchni silikonowych
- Zapewnia bardzo dobrą izolację dźwiękową i cieplną
- Podwyższona wydajność o 15% w stosunku do piany o standardowej objętości pojemnika
- Klasa F reakcja na ogień wg. PN-EN 13501-1+A1:2010.
- Powierzchnia, na którą wykonywana jest aplikacja musi być wolna od kurzu, luźnych cząstek i oleju
- Powierzchnia, na którą wykonujemy aplikację, powinna być dobrze zwilżona. Brak odpowiedniej wilgotności może wywołać wtórne rozprężanie
- Przy aplikacji w niskich temperaturach pojemnik z pianą zimową należy podgrzać przed rozpoczęciem pracy w ciepłym pomieszczeniu lub wodzie. Temperatura pomieszczenia lub wody nie powinna przekraczać +30°C
- Przed aplikacją należy wstrząsnąć energicznie pojemnik z pianą przynajmniej 20 razy
- Ilość wypływającej piany należy regulować za pomocą spustu pistoletu
- Po utwardzeniu piana nie jest odporna na promieniowanie UV i musi zostać zakryta w ciągu 24h. Niezabezpieczona piana robi się krucha. Piana może być malowana farbami na bazie wody
- Pozostałości piany można oczyścić przy pomocy produktów Premium Foam Cleaner, Premium Foam Remover lub przy pomocy chusteczek Premium Cleaning Wipes. Szczegóły podano w kartach tych produktów
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Temperatura pracy | Objętość | Sposób aplikacji | Termin przydatności | Wersja | Opakowanie | Karton zbiorczy | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | miesiące | - | szt. | szt. | ||
A1493 | 4742205009681 | POJEMNIK | +5 | +30 | 900 | PISTOLET | 18 | LETNIA | 1 | 12 |
A1540 | 4742640000793 | POJEMNIK | -10 | +30 | 900 | PISTOLET | 18 | ZIMOWA | 1 | 12 |
Właściwości | Jednostka | Wartość |
Czas formowania naskórka | minuta | 10-12 |
Czas ścinania (30 mm pasek) | minuta | 30-35 |
Całkowite utwardzenie w szczelinie (w temp. +23 °C) | godzina | do 12 |
Całkowite utwardzenie w szczelinie (w temp. +5 °C) | godzina | do 20 |
Gęstość | kg/m3 | 20-25 |
Klasa reakcji na ogień utwardzonej pianki (PN-EN 13501-1+A1:2010 ) | - | F |
Zmniejszona objętość | % | brak |
Ekspansja wtórna | % | do 33 |
Temperatura zapłonu utwardzonej pianki | °C | 400 |
Wytrzymałość na rozciąganie (BS 5241 ) | N/cm2 | 9 |
Wytrzymałość na ściskanie przy 10% odkształceniu (DIN 53421 ) | N/cm2 | 3 |
Przewodność cieplna | W/m*K | 0,034 |
Wskaźnik izolacyjności akustycznej | dB | RST,w = 60 |
Odporność termiczna po utwardzeniu | °C | długi okres: -50 do +90 krótki okres: -65 do +130 |
Podane powyżej wartości uzyskano w temperaturze +23°C i przy względnej wilgotności 50%, chyba że podano inaczej. |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Diversity is only limited by imagination
PENOSIL GOLDGUN 65 PLUS
Niskoprężna piana pistoletowa całoroczna o wysokiej wydajności do wypełniania szczelin

- Jednoskładnikowa piana poliuretanowa o wysokiej wydajności, jednorodnej bardzo lekkiej strukturze i niskiej ekspansji wtórnej, dostarczana w puszkach z aerozolem
- Piana w kolorze jasnożółtym
- Piana występuje wyłącznie w wersji całorocznej
- Dobrze przylega do większości materiałów budowlanych, z wyjątkiem teflonu, polietylenu i powierzchni silikonowych
- Zapewnia bardzo dobrą izolację dźwiękową i cieplną. Odporna na działanie wilgoci i pleśni
- Zwiększona wydajność o 30% w stosunku do piany o standardowej objętości pojemnika
- Klasa F reakcja na ogień wg. PN-EN 13501-1+A1:2010.
- Powierzchnia, na którą wykonywana jest aplikacja musi być wolna od kurzu, luźnych cząstek i oleju
- Powierzchnia, na którą wykonujemy aplikację, powinna być dobrze zwilżona. Brak odpowiedniej wilgotności może wywołać wtórne rozprężanie
- Przy aplikacji w niskich temperaturach pojemnik z pianą należy podgrzać przed rozpoczęciem pracy w ciepłym pomieszczeniu lub wodzie. Temperatura pomieszczenia lub wody nie powinna przekraczać +30°C
- Przed aplikacją należy wstrząsnąć energicznie pojemnik z pianą przynajmniej 20 razy
- Ilość wypływającej piany należy regulować za pomocą spustu pistoletu
- Po utwardzeniu piana nie jest odporna na promieniowanie UV i musi zostać zakryta w ciągu 24h. Niezabezpieczona piana robi się krucha. Piana może być malowana farbami na bazie wody
- Pozostałości piany można oczyścić przy pomocy produktów Premium Foam Cleaner, Premium Foam Remover lub przy pomocy chusteczek Premium Cleaning Wipes. Szczegóły podano w kartach tych produktów
- Szczegółowe informacje dotyczące przechowywania, transportu i bezpieczeństwa są dostępne w karcie charakterystyki (SDS).

Kod produktu | Numer EAN | Postać | Temperatura pracy | Objętość | Sposób aplikacji | Termin przydatności | Wersja | Opakowanie | Karton zbiorczy | |
MIN | MAX | |||||||||
- | °C | °C | ml | - | miesiące | - | szt. | szt. | ||
A3348 | 4742640008171 | POJEMNIK | -20 | +30 | 850 | PISTOLET | 18 | CAŁOROCZNA | 1 | 12 |
Właściwości | Jednostka | Wartość |
Czas formowania naskórka | minuta | 8-10 |
Czas ścinania (30 mm pasek) | minuta | 25-30 |
Całkowite utwardzenie w szczelinie (w temp. +23 °C) | godzina | do 12 |
Całkowite utwardzenie w szczelinie (w temp. +5 °C) | godzina | do 18 |
Gęstość | kg/m3 | 17-20 |
Klasa reakcji na ogień utwardzonej pianki (PN-EN 13501-1+A1:2010 ) | - | F |
Zmniejszona objętość | % | brak |
Ekspansja wtórna | % | do 30 |
Temperatura zapłonu utwardzonej pianki | °C | 400 |
Wytrzymałość na rozciąganie (BS 5241 ) | N/cm2 | 8 |
Wytrzymałość na ściskanie przy 10% odkształceniu (DIN 53421 ) | N/cm2 | 2,5 |
Przewodność cieplna | W/m*K | 0,034 |
Wskaźnik izolacyjności akustycznej | dB | RST,w = 60 |
Odporność termiczna po utwardzeniu | °C | długi okres: -50 do +90 krótki okres: -65 do +130 |
Podane powyżej wartości uzyskano w temperaturze +23°C i przy względnej wilgotności 50%, chyba że podano inaczej. |
Nie zapomnij o akcesoriach!!!

Pozostałe produkty
Sprawdź co jeszcze możesz zamontować dzięki naszym produktom.
Eurofast oferuje szeroką gamę wysokiej jakości chemii budowlanej takiej jak: piana montażowa, piana montażowa ogniochronna, silikon, klej-uszczelniacz, uszczelniacz budowlany, taśma butylowa. Zgodnie z obowiązującą dyrektywą w sprawie charakterystyka energetyczna budynków określa się, że wszystkie nowe budynki wybudowane po 31 grudnia 2020 muszą być budynkami o bardzo niskim zużyciu energii. Aby spełnić wymagania nałożone przez dyrektywę, należy używać odpowiednie produkty do izolacji i uszczelniania, zapewniające niskie straty ciepła. Oferta Eurofast wychodzi naprzeciw wymaganiom dyrektywy.
Podstawą oferty są produkty znanej w ponad 50 krajach firmy Penosil oraz firmy Olive, będących wiodącymi producentami chemii budowlanej. Jakość oferowanych produktów postawiona jest na najwyższym poziomie. Piana montażowa posiada dokumenty: aprobata techniczna ITB, krajowa ocena techniczna ITB. Piany montażowe, silikony i uszczelniacze budowlane znajdujące się w prezentowanym programie skierowane są do najbardziej wymagających klientów – profesjonalnych montażystów. Szeroka gama wysokiej jakości produktów nadaje się również do użytku domowego. Gwarantujemy najwyższą jakość produktów, serwis oraz ceny. Ciepły montaż to główna gama produktów dostarczanych przez Eurofast. Zalety pian montażowych to: niskoprężność, wysoka wydajność, krótki czas wiązania, struktura. Wtórne rozprężanie piany montażowej to przeszłość w przypadku produktów firmy Penosil. Poza produktami, dostarczamy również akcesoria montażowe: pistolet do piany, wyciskacz do piany, środek czyszczący do piany montażowej, pistolet do silikonu, ściereczki czyszczące.

Pozostałe produkty
Sprawdź co jeszcze możesz zmienić dzięki naszym produktom.
Diversity is only limited by imagination
E-X BOHR RS 4,8 x 35 with washer E14
Stainless self-drilling screws for fixing roof tiles

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 2 x 1,00 mm
- For installation, use cappers with a maximum speed of 2200 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
steel/steel | ||||||||||
mm | - | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72010602 | 0000720106020 | 4,8 x 35 | zinc | 2x0,75 | 22 | 2x1,00 | 8 | 14 | 1000 | - |
- h min – when connecting steel sheets together is the minimum thickness of those sheets.
- h max - when connecting steel sheets together is the maximum thickness of those sheets.
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR RS 4,8xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | - | 0,70 | 1,00 | 1,30 | 1,30 | 1,30 | - | - | ||
0,75 | - | 0,90 | 1,20 | 1,50 | 1,60 | 1,70 | - | - | ||
0,88 | - | 1,10 | 1,40 | 1,80 | 2,00 | - | - | - | ||
1,00 | - | 1,20 | 1,60 | 2,00 | - | - | - | - | ||
1,13 | - | 1,40 | 1,80 | - | - | - | - | - | ||
1,25 | - | 1,60 | - | - | - | - | - | - | ||
1,50 | - | - | - | - | - | - | - | - | ||
1,75 | - | - | - | - | - | - | - | - | ||
2,00 | - | - | - | - | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR RS 4,8xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | 0,40 | 0,50 | 0,60 | 0,70 | 0,90 | 0,90 | - | - | ||
0,75 | 0,40 | 0,50 | 0,60 | 0,70 | 0,90 | 1,00 | - | - | ||
0,88 | 0,40 | 0,50 | 0,60 | 0,80 | 1,10 | - | - | - | ||
1,00 | 0,40 | 0,50 | 0,60 | 0,80 | - | - | - | - | ||
1,13 | 0,40 | 0,50 | 0,70 | - | - | - | - | - | ||
1,25 | 0,40 | 0,50 | 0,70 | - | - | - | - | - | ||
1,50 | - | - | - | - | - | - | - | - | ||
1,75 | - | - | - | - | - | - | - | - | ||
2,00 | - | - | - | - | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR RS 6,5 x L with washer E16
Stainless self-drilling screws for fixing steel sheets to wooden substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Anchoring depth in wood min 30 mm
- Maximum drilling capacity in steel up to 2,00 mm
- For installation, use cappers with a maximum speed of 1800 rpm with regulated torque
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
steel/wood | ||||||||||
hef = min. 30 mm | ||||||||||
mm | - | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72011103 | 0000720111031 | 6,5 x 50 | zinc | 0,63 | 20 | 2,00 | 8 | 16 | 500 | - |
72011203 | 0000720112038 | 6,5 x 65 | zinc | 0,63 | 35 | 2,00 | 8 | 16 | 400 | - |
- h min – when fixing steel sheets to wooden substrate is the minimum thickness of the steel sheet that can be fixed
- h max - when fixing steel sheets to wooden substrate is the maximum thickness of the fixed elements. Is the sum of: the thickness of the steel sheet and the thickness of components located between the substrate and steel sheet or the thickness of the air gap. Embedment depth in wood was already counted.
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Effective embedment depth in wood hef [mm] 2) | ||||||||||
30,00 | 35,00 | 40,00 | 45,00 | 50,00 | 55,00 | 60,00 | 65,00 | |||
E-X BOHR RS 6,5xL | 0,50 | - | ||||||||
0,55 | - | |||||||||
0,63 | 1,16 | |||||||||
0,75 | 1,30 | |||||||||
0,88 | 1,39 | |||||||||
1,00 | 1,46 | |||||||||
1,13 | 1,49 | |||||||||
1,25 | 1,51 | |||||||||
1,50 | 1,53 | |||||||||
1,75 | 1,59 | |||||||||
2,00 | 1,78 |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) construction wood according to EN 14081

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Effective embedment depth in wood hef [mm] 2) | ||||||||||
30,00 | 35,00 | 40,00 | 45,00 | 50,00 | 55,00 | 60,00 | 65,00 | |||
E-X BOHR RS 6,5xL | 0,50 | - | ||||||||
0,55 | - | |||||||||
0,63 | 1,68 | 1,99 | 2,30 | 2,61 | 2,87 | |||||
0,75 | 2,91 | |||||||||
0,88 | 2,95 | |||||||||
1,00 | ||||||||||
1,13 | ||||||||||
1,25 | ||||||||||
1,50 | ||||||||||
1,75 | ||||||||||
2,00 |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) construction wood according to EN 14081

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR 5 5,5 x 38 with washer E16
Stainless self-drilling screws for fixing steel sheets to the steel substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 12,50 mm
- For installation, use cappers with a maximum speed of 1500 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | - | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72050803 | 0000720508039 | 5,5 x 38 | zinc | 6,00+0,63 | 11 | 12,50 | 8 | 16 | 800 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: the minimum thickness of the substrate and the minimum thickness of the steel sheet tested with specific screw type
- h max - maximum thickness of the fixed elements. Is the sum of: the thickness of the substrate, the thickness of the steel sheet and the thickness of components located between the substrate and steel sheet or the thickness of the air gap
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
4,00 | 5,00 | 6,00 | 8,00 | 10,00 | 12,00 | 13,00 | 14,00 | |||
E-X BOHR 5 5,5xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | - | - | 4,00 | 4,00 | 4,00 | - | - | - | ||
0,75 | - | - | 4,50 | 4,50 | 4,50 | - | - | - | ||
0,88 | - | - | 4,90 | 5,00 | 5,00 | - | - | - | ||
1,00 | - | - | 5,30 | 5,40 | 5,50 | - | - | - | ||
1,13 | - | - | 5,70 | 5,90 | 6,00 | - | - | - | ||
1,25 | - | - | 6,10 | 6,30 | 6,50 | - | - | - | ||
1,50 | - | - | 6,10 | 6,30 | 6,50 | - | - | - | ||
1,75 | - | - | 6,10 | 6,30 | 6,50 | - | - | - | ||
2,00 | - | - | 6,10 | 6,30 | 6,50 | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness2), [mm] | ||||||||||
4,00 | 5,00 | 6,00 | 8,00 | 10,00 | 12,00 | 13,00 | 14,00 | |||
E-X BOHR 5 5,5xL | 0,50 | - | - | 1,84 | 1,84 | 1,84 | - | - | - | |
0,55 | - | - | 2,32 | 2,32 | 2,32 | - | - | - | ||
0,63 | - | - | 3,40 | 3,40 | 3,40 | - | - | - | ||
0,75 | - | - | 3,90 | 3,90 | 3,90 | - | - | - | ||
0,88 | - | - | 4,40 | 4,40 | 4,40 | - | - | - | ||
1,00 | - | - | 4,90 | 4,90 | 4,90 | - | - | - | ||
1,13 | - | - | 5,40 | 5,40 | 5,40 | - | - | - | ||
1,25 | - | - | 5,80 | 5,80 | 5,80 | - | - | - | ||
1,50 | - | - | 6,60 | 6,60 | 6,60 | - | - | - | ||
1,75 | - | - | 6,60 | 6,60 | 6,60 | - | - | - | ||
2,00 | - | - | 6,60 | 6,60 | 6,60 | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR 3 5,5 x 32 with washer E16
Stainless self-drilling screws for fixing steel sheets to the steel substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 5,50 mm
- For installation, use cappers with a maximum speed of 1500 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | - | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72040703 | 0000720407035 | 5,5 x 32 | zinc | 1,50+0,63 | 16 | 5,50 | 8 | 16 | 800 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: the minimum thickness of the substrate and the minimum thickness of the steel sheet tested with specific screw type
- h max - maximum thickness of the fixed elements. Is the sum of: the thickness of the substrate, the thickness of the steel sheet and the thickness of components located between the substrate and steel sheet or the thickness of the air gap
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
1,50 | 2,00 | 2,50 | 3,00 | 4,00 | 5,00 | 6,00 | 7,00 | |||
E-X BOHR 3 5,5xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | 2,40 | 2,40 | 2,40 | 2,40 | 2,40 | - | - | - | ||
0,75 | 2,70 | 2,80 | 2,80 | 3,30 | 3,30 | - | - | - | ||
0,88 | 3,00 | 3,50 | 3,50 | 4,20 | 4,20 | - | - | - | ||
1,00 | 3,20 | 3,60 | 3,60 | 4,30 | 4,30 | - | - | - | ||
1,13 | 3,20 | 3,60 | 3,60 | 4,30 | 4,30 | - | - | - | ||
1,25 | 3,20 | 3,60 | 3,60 | 4,30 | 4,30 | - | - | - | ||
1,50 | 3,20 | 3,60 | 3,60 | 4,30 | - | - | - | - | ||
1,75 | 3,20 | 3,60 | 3,60 | 4,30 | - | - | - | - | ||
2,00 | 3,20 | 3,60 | 3,60 | 4,30 | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness2), [mm] | ||||||||||
1,50 | 2,00 | 2,50 | 3,00 | 4,00 | 5,00 | 6,00 | 7,00 | |||
E-X BOHR 3 5,5xL | 0,50 | 0,54 | 0,97 | 0,97 | 1,57 | 1,57 | - | - | - | |
0,55 | 0,88 | 1,23 | 1,23 | 1,98 | 1,98 | - | - | - | ||
0,63 | 1,00 | 1,80 | 1,80 | 2,90 | 2,90 | - | - | - | ||
0,75 | 1,00 | 1,80 | 1,80 | 3,50 | 3,50 | - | - | - | ||
0,88 | 1,00 | 1,80 | 1,80 | 4,10 | 4,10 | - | - | - | ||
1,00 | 1,00 | 1,80 | 1,80 | 4,60 | 4,70 | - | - | - | ||
1,13 | 1,00 | 1,80 | 1,80 | 4,60 | 5,40 | - | - | - | ||
1,25 | 1,00 | 1,80 | 1,80 | 4,60 | 6,00 | - | - | - | ||
1,50 | 1,00 | 1,80 | 1,80 | 4,60 | - | - | - | - | ||
1,75 | 1,00 | 1,80 | 1,80 | 4,60 | - | - | - | - | ||
2,00 | 1,00 | 1,80 | 1,80 | 4,60 | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR 2 5,5 x L with washer E16
Stainless self-drilling screws for fixing steel sheets to the steel substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 3,50 mm
- For installation, use cappers with a maximum speed of 1800 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | - | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72030603 | 0000720306031 | 5,5 x 25 | zinc | 1,00+0,63 | 8 | 3,50 | 8 | 16 | 1000 | - |
72030703 | 0000720307038 | 5,5 x 38 | zinc | 1,00+0,63 | 21 | 3,50 | 8 | 16 | 800 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: the minimum thickness of the substrate and the minimum thickness of the steel sheet tested with specific screw type
- h max - maximum thickness of the fixed elements. Is the sum of: the thickness of the substrate, the thickness of the steel sheet and the thickness of components located between the substrate and steel sheet or the thickness of the air gap
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR 2 5,5xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | - | - | - | 1,20 | 1,50 | 1,70 | 1,70 | 1,70 | ||
0,75 | - | - | - | 1,60 | 1,80 | 2,00 | 2,00 | 2,00 | ||
0,88 | - | - | - | 2,00 | 2,20 | 2,30 | 2,40 | 2,40 | ||
1,00 | - | - | - | 2,20 | 2,60 | 2,70 | 2,70 | 2,70 | ||
1,13 | - | - | - | 2,20 | 2,60 | 2,70 | 2,70 | 2,70 | ||
1,25 | - | - | - | 2,20 | 2,60 | 2,70 | 2,70 | 2,70 | ||
1,50 | - | - | - | 2,20 | 2,60 | 2,70 | 2,70 | 2,70 | ||
1,75 | - | - | - | 2,20 | 2,60 | 2,70 | 2,70 | - | ||
2,00 | - | - | - | 2,20 | 2,60 | 2,70 | 2,70 | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR 2 5,5xL | 0,50 | - | - | - | 0,38 | 0,43 | 0,54 | 0,76 | 1,19 | |
0,55 | - | - | - | 0,48 | 0,55 | 0,68 | 0,95 | 1,50 | ||
0,63 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
0,75 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
0,88 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
1,00 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
1,13 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
1,25 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
1,50 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | 2,20 | ||
1,75 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | - | ||
2,00 | - | - | - | 0,70 | 0,80 | 1,00 | 1,40 | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR RS 5,5 x22 with washer E16
Stainless self-drilling screws for connecting steel sheets

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 2 x 1,00 mm
- For installation, use cappers with a maximum speed of 2200 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | - | mm | mm | mm | mm | mm | szt. | szt. | ||
72010803 | 0000720108031 | 5,5 x 22 | zinc | 2x0,75 | 7 | 2x1,00 | 8 | 16 | 1000 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: the minimum thickness of the substrate and the minimum thickness of the steel sheet tested with specific screw type
- h max - maximum thickness of the fixed elements. Is the sum of: the thickness of the substrate, the thickness of the steel sheet and the thickness of components located between the substrate and steel sheet or the thickness of the air gap
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR RS 5,5xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | - | 1,20 | 1,30 | 1,80 | 2,10 | 2,80 | - | - | ||
0,75 | - | 1,30 | 1,60 | 2,00 | 2,40 | 3,00 | - | - | ||
0,88 | - | 1,40 | 1,80 | 2,20 | 2,70 | - | - | - | ||
1,00 | - | 1,50 | 2,00 | 2,40 | - | - | - | - | ||
1,13 | - | 1,60 | 2,00 | - | - | - | - | - | ||
1,25 | - | 1,70 | - | - | - | - | - | - | ||
1,50 | - | - | - | - | - | - | - | - | ||
1,75 | - | - | - | - | - | - | - | - | ||
2,00 | - | - | - | - | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR RS 5,5xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | 0,50 | 0,70 | 0,90 | 0,90 | 0,90 | 0,90 | - | - | ||
0,75 | 0,50 | 0,70 | 1,00 | 1,00 | 1,00 | 1,00 | - | - | ||
0,88 | 0,70 | 0,90 | 1,10 | 1,20 | 1,20 | - | - | - | ||
1,00 | 0,70 | 0,90 | 1,10 | 1,40 | - | - | - | - | ||
1,13 | 0,80 | 1,00 | 1,30 | - | - | - | - | - | ||
1,25 | 0,80 | 1,00 | - | - | - | - | - | - | ||
1,50 | - | - | - | - | - | - | - | - | ||
1,75 | - | - | - | - | - | - | - | - | ||
2,00 | - | - | - | - | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR RS 4,8 x20 with washer E14
Stainless self-drilling screws for connecting steel sheets

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 2 x 1,00 mm
- For installation, use cappers with a maximum speed of 2200 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-11/0174

Product code | EAN code | DxL | Color | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | - | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72010402 | 0000720104026 | 4,8 x 20 | cynk | 2x0,75 | 7 | 2x1,00 | 8 | 14 | 1000 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: the minimum thickness of the substrate and the minimum thickness of the steel sheet tested with specific screw type
- h max - maximum thickness of the fixed elements. Is the sum of: the thickness of the substrate, the thickness of the steel sheet and the thickness of components located between the substrate and steel sheet or the thickness of the air gap
Fastener designation | Steel sheet thickness1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR RS 4,8xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | - | 0,70 | 1,00 | 1,30 | 1,30 | 1,30 | - | - | ||
0,75 | - | 0,90 | 1,20 | 1,50 | 1,60 | 1,70 | - | - | ||
0,88 | - | 1,10 | 1,40 | 1,80 | 2,00 | - | - | - | ||
1,00 | - | 1,20 | 1,60 | 2,00 | - | - | - | - | ||
1,13 | - | 1,40 | 1,80 | - | - | - | - | - | ||
1,25 | - | 1,60 | - | - | - | - | - | - | ||
1,50 | - | - | - | - | - | - | - | - | ||
1,75 | - | - | - | - | - | - | - | - | ||
2,00 | - | - | - | - | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Steel sheet thickness1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness2), [mm] | ||||||||||
0,63 | 0,75 | 0,88 | 1,00 | 1,13 | 1,25 | 1,50 | 2,00 | |||
E-X BOHR RS 4,8xL | 0,50 | - | - | - | - | - | - | - | - | |
0,55 | - | - | - | - | - | - | - | - | ||
0,63 | 0,40 | 0,50 | 0,60 | 0,70 | 0,90 | 0,90 | - | - | ||
0,75 | 0,40 | 0,50 | 0,60 | 0,70 | 0,90 | 1,00 | - | - | ||
0,88 | 0,40 | 0,50 | 0,60 | 0,80 | 1,10 | - | - | - | ||
1,00 | 0,40 | 0,50 | 0,60 | 0,80 | - | - | - | - | ||
1,13 | 0,40 | 0,50 | 0,70 | - | - | - | - | - | ||
1,25 | 0,40 | 0,50 | 0,70 | - | - | - | - | - | ||
1,50 | - | - | - | - | - | - | - | - | ||
1,75 | - | - | - | - | - | - | - | - | ||
2,00 | - | - | - | - | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD according to EN 10346
2) steel grade S235 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR RS HT 7,0/6,5xL with washer E19
Stainless self-drilling screws for fixing sandwich panels to wooden substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 2×1,00 mm
- Anchoring depth in wood min 50 mm
- For installation, use power screwdriver with a maximum speed of 1500 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-13/0181

Product code | EAN code | D1/DxL | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72081204 | 0000720812037 | 7,0/6,5 x 80 | 10 | 30 | 2,00 | 8 | 19 | 250 | - |
72081404 | 0000720814031 | 7,0/6,5 x 100 | 30 | 50 | 2,00 | 8 | 19 | 200 | - |
72081604 | 0000720816035 | 7,0/6,5 x 120 | 50 | 70 | 2,00 | 8 | 19 | 150 | - |
72081704 | 0000720817032 | 7,0/6,5 x 140 | 70 | 90 | 2,00 | 8 | 19 | 150 | - |
72081804 | 0000720818039 | 7,0/6,5 x 160 | 90 | 110 | 2,00 | 8 | 19 | 150 | - |
72081904 | 0000720819036 | 7,0/6,5 x 180 | 110 | 130 | 2,00 | 8 | 19 | 150 | - |
72082004 | 0000720820032 | 7,0/6,5 x 200 | 130 | 150 | 2,00 | 8 | 19 | 150 | - |
72082104 | 0000720821039 | 7,0/6,5 x 220 | 150 | 170 | 2,00 | 8 | 19 | 150 | - |
72082404 | 0000720824030 | 7,0/6,5 x 240 | 170 | 190 | 2,00 | 8 | 19 | 100 | - |
72082804 | 0000720828038 | 7,0/6,5 x 275 | 205 | 225 | 2,00 | 8 | 19 | 100 | - |
72083004 | 0000720830031 | 7,0/6,5 x 300 | 230 | 250 | 2,00 | 8 | 19 | 50 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: sandwich panel thickness at the fixing point, the insulating tape thickness or saddle washers thickness if any.
- h max - maximum thickness of the fixed elements. Is the sum of: sandwich panel thickness at the fixing point, the insulating tape thickness or saddle washers thickness if any.
Fastener designation | Sandwich panel lining thickness 1), [mm] | Characteristic share load, [kN]* | |||||||
---|---|---|---|---|---|---|---|---|---|
Effective embedment depth in wood hef ≥ 50mm 2) | |||||||||
Sandwich panel thickness | |||||||||
40,00 | 50,00 | 60,00 | 70,00 | 80,00 | 100,00 | 120,00 | 140,00 | ||
E-X BOHR RS HT 6,5xL | 0,40 | - | - | - | - | - | - | - | - |
0,50 | 1,56 | 1,56 | 1,56 | 1,56 | 1,56 | - | - | - | |
0,55 | 1,78 | 1,78 | 1,78 | 1,78 | 1,78 | - | - | - | |
0,63 | 2,13 | 2,13 | 2,13 | 2,13 | 2,13 | - | - | - | |
0,75 | 2,51 | 2,65 | 2,65 | 2,65 | 2,65 | - | - | - | |
0,88 | 2,51 | 3,14 | 3,22 | 3,22 | 3,22 | - | - | - | |
1,00 | 2,51 | 3,14 | 3,68 | 3,74 | 3,74 | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) construction wood according to EN 14081

Fastener designation | Sandwich panel lining thickness 1), [mm] | Characteristic tension load, [kN]* | |||||||
---|---|---|---|---|---|---|---|---|---|
Effective embedment depth in wood hef ≥ 50mm 2) | |||||||||
Sandwich panel thickness | |||||||||
40,00 | 50,00 | 60,00 | 70,00 | 80,00 | 100,00 | 120,00 | ≥140,00 | ||
E-X BOHR RS HT 6,5xL | 0,40 | - | - | - | - | - | - | - | - |
0,50 | 2,00 | 2,00 | 2,00 | 2,00 | 2,00 | - | - | - | |
0,55 | 2,00 | 2,00 | 2,00 | 2,00 | 2,00 | - | - | - | |
0,63 | 2,00 | 2,00 | 2,00 | 2,00 | 2,00 | - | - | - | |
0,75 | 2,00 | 2,00 | 2,00 | 2,00 | 2,00 | - | - | - | |
0,88 | 2,00 | 2,00 | 2,00 | 2,00 | 2,00 | - | - | - | |
1,00 | 2,00 | 2,00 | 2,00 | 2,00 | 2,00 | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) construction wood according to EN 14081

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR 5 HT 6,3/5,5xL with washer E19
Stainless self-drilling screws for fixing sandwich panels to the steel substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 12,50 mm
- For installation, use cappers with a maximum speed of 1500 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-13/0181

Product code | EAN code | D1/DxL | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72071104 | 0000720711033 | 6,3/5,5 x 75 | 30 | 46 | 12,5 | 8 | 19 | 300 | - |
72071504 | 0000720715031 | 6,3/5,5 x 95 | 35 | 66 | 12,5 | 8 | 19 | 250 | - |
72071604 | 0000720716038 | 6,3/5,5 x 110 | 50 | 81 | 12,5 | 8 | 19 | 200 | - |
72071794 | 0000720717943 | 6,3/5,5 x 130 | 70 | 101 | 12,5 | 8 | 19 | 150 | - |
72071804 | 0000720718032 | 6,3/5,5 x 150 | 90 | 121 | 12,5 | 8 | 19 | 150 | - |
72071904 | 0000720719039 | 6,3/5,5 x 165 | 105 | 136 | 12,5 | 8 | 19 | 150 | - |
72072094 | 0000720720943 | 6,3/5,5 x 190 | 130 | 161 | 12,5 | 8 | 19 | 150 | - |
72072104 | 0000720721032 | 6,3/5,5 x 210 | 150 | 181 | 12,5 | 8 | 19 | 150 | - |
72072304 | 0000720723036 | 6,3/5,5 x 240 | 180 | 211 | 12,5 | 8 | 19 | 100 | - |
72072704 | 0000720727034 | 6,3/5,5 x 270 | 210 | 241 | 12,5 | 8 | 19 | 100 | - |
72072904 | 0000720729038 | 6,3/5,5 x 290 | 230 | 261 | 12,5 | 8 | 19 | 100 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: sandwich panel thickness at the fixing point, the thickness of the substrate, the insulating tape thickness or saddle washers thickness if any.
- h max - maximum thickness of the fixed elements. Is the sum of: sandwich panel thickness at the fixing point, the thickness of the substrate, the insulating tape thickness or saddle washers thickness if any.
Fastener designation | Sandwich panel lining thickness 1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
1,50 | 2.00 | 2.50 | 3.00 | 4.00 | 5.00 | 6.00 | 8.00 | ≥10,00 | ||
E-X BOHR 5 HT 5,5xL | 0,40 | - | - | - | - | - | - | - | - | - |
0,50 | - | - | - | 1,18 | 1,20 | 1,23 | 1,23 | 1,23 | 1,30 | |
0,55 | - | - | - | 1,58 | 1,61 | 1,65 | 1,65 | 1,65 | 1,70 | |
0,63 | - | - | - | 2,21 | 2,25 | 2,31 | 2,31 | 2,31 | 2,40 | |
0,75 | - | - | - | 3,17 | 3,24 | 3,31 | 3,31 | 3,31 | 3,40 | |
0,88 | - | - | - | 3,50 | 3,58 | 3,66 | 3,66 | 3,66 | 3,70 | |
1,00 | - | - | - | 3,81 | 3,89 | 3,98 | 3,98 | 3,98 | 4,00 |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) steel grade S235, S275, S355 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Sandwich panel lining thickness 1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
1,50 | 2.00 | 2.50 | 3.00 | 4.00 | 5.00 | 6.00 | 8.00 | ≥10,00 | ||
E-X BOHR 5 HT 5,5xL | 0,40 | - | - | - | - | - | - | - | - | - |
0,50 | - | - | - | 2,40 | 2,40 | 2,40 | 2,40 | 2,40 | 2,40 | |
0,55 | - | - | - | 2,60 | 2,60 | 2,60 | 2,60 | 2,60 | 2,60 | |
0,63 | - | - | - | 3,00 | 3,00 | 3,00 | 3,00 | 3,00 | 3,00 | |
0,75 | - | - | - | 3,60 | 3,60 | 3,60 | 3,60 | 3,60 | 3,60 | |
0,88 | - | - | - | 4,20 | 4,20 | 4,20 | 4,20 | 4,20 | 4,20 | |
1,00 | - | - | - | 4,70 | 4,70 | 4,70 | 4,70 | 4,70 | 4,70 |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) steel grade S235, S275, S355 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination
E-X BOHR 3 HT 6,3/5,5xL with washer E19
Stainless self-drilling screws for fixing sandwich panels to the steel substrate

- Screws are made of stainless steel with drilling point made of surface-hardened carbon steel, zinc plated
- Washer is made of stainless steel with vulcanized EPDM layer
- Screw heads and washers may be coated with lacquer coating
- Maximum drilling capacity in steel up to 5,50 mm
- For installation, use cappers with a maximum speed of 1500 rpm with regulated torque
- Screws for corrosivity class C4
- Screws in class A1 – reaction to fire
- ETA-13/0181

Product code | EAN code | D1/DxL | hmin | hmax | Max. drilling capacity | Head size | Washer diameter | Single box | Outer cartoon |
mm | mm | mm | mm | mm | mm | pcs. | pcs. | ||
72061104 | 0000720611036 | 6,3/5,5 x 70 | 24 | 51 | 5,50 | 8 | 19 | 300 | - |
72061204 | 0000720612033 | 6,3/5,5 x 85 | 39 | 66 | 5,50 | 8 | 19 | 250 | - |
72061304 | 0000720613030 | 6,3/5,5 x 95 | 49 | 76 | 5,50 | 8 | 19 | 250 | - |
72061504 | 0000720615034 | 6,3/5,5 x 110 | 64 | 91 | 5,50 | 8 | 19 | 200 | - |
72061704 | 0000720617038 | 6,3/5,5 x 130 | 64 | 111 | 5,50 | 8 | 19 | 150 | - |
72061804 | 0000720618035 | 6,3/5,5 x 150 | 84 | 131 | 5,50 | 8 | 19 | 150 | - |
72061904 | 0000720619032 | 6,3/5,5 x 165 | 99 | 146 | 5,50 | 8 | 19 | 150 | - |
72062004 | 0000720620038 | 6,3/5,5 x 180 | 104 | 161 | 5,50 | 8 | 19 | 150 | - |
72062104 | 0000720621035 | 6,3/5,5 x 200 | 124 | 181 | 5,50 | 8 | 19 | 150 | - |
72062304 | 0000720623039 | 6,3/5,5 x 230 | 154 | 211 | 5,50 | 8 | 19 | 150 | - |
72062504 | 0000720625033 | 6,3/5,5 x 250 | 174 | 231 | 5,50 | 8 | 19 | 100 | - |
72062704 | 0000720627037 | 6,3/5,5 x 270 | 194 | 251 | 5,50 | 8 | 19 | 100 | - |
72062904 | 0000720629031 | 6,3/5,5 x 290 | 214 | 271 | 5,50 | 8 | 19 | 100 | - |
- h min - minimum thickness of the fixed elements. Is the sum of: sandwich panel thickness at the fixing point, the thickness of the substrate, the insulating tape thickness or saddle washers thickness if any.
- h max - maximum thickness of the fixed elements. Is the sum of: sandwich panel thickness at the fixing point, the thickness of the substrate, the insulating tape thickness or saddle washers thickness if any.
Fastener designation | Sandwich panel lining thickness 1), [mm] | Characteristic share load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
1,50 | 2.00 | 2.50 | 3.00 | 4.00 | 5.00 | 6.00 | 8.00 | ≥10,00 | ||
E-X BOHR 3 HT 5,5xL | 0,40 | - | - | - | - | - | - | - | - | - |
0,50 | 1,36 | 1,45 | 1,50 | 1,55 | 1,63 | - | - | - | - | |
0,55 | 1,53 | 1,63 | 1,68 | 1,74 | 1,83 | - | - | - | - | |
0,63 | 1,80 | 1,91 | 1,98 | 2,04 | 2,15 | - | - | - | - | |
0,75 | 2,20 | 2,34 | 2,42 | 2,50 | 2,64 | - | - | - | - | |
0,88 | 2,53 | 2,63 | 2,69 | 2,75 | 2,88 | - | - | - | - | |
1,00 | 2,83 | 2,90 | 2,94 | 2,99 | 3,10 | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) steel grade S235, S275, S355 according to EN 10025-1; S280GD, S320GD according to EN 10346

Fastener designation | Sandwich panel lining thickness 1), [mm] | Characteristic tension load, [kN]* | ||||||||
---|---|---|---|---|---|---|---|---|---|---|
Steel substrate thickness 2), [mm] | ||||||||||
1,50 | 2.00 | 2.50 | 3.00 | 4.00 | 5.00 | 6.00 | 8.00 | ≥10,00 | ||
E-X BOHR 3 HT 5,5xL | 0,40 | - | - | - | - | - | - | - | - | - |
0,50 | 2,10 | 2,20 | 2,20 | 2,20 | 2,20 | - | - | - | - | |
0,55 | 2,10 | 2,60 | 2,60 | 2,60 | 2,60 | - | - | - | - | |
0,63 | 2,10 | 3,00 | 3,00 | 3,00 | 3,00 | - | - | - | - | |
0,75 | 2,10 | 3,20 | 3,70 | 3,70 | 3,70 | - | - | - | - | |
0,88 | 2,10 | 3,20 | 3,80 | 3,80 | 3,80 | - | - | - | - | |
1,00 | 2,10 | 3,20 | 4,00 | 4,00 | 4,00 | - | - | - | - |
* In order to determine the design resistance characteristic value should be divided by a safety factor of 1.33
1) steel grade S280GD, S320GD, S350GD according to EN 10346
2) steel grade S235, S275, S355 according to EN 10025-1; S280GD, S320GD according to EN 10346

Connected products. Do not forget about accessories!!!

Other Categories
Check out what else can be fixed with our products
Diversity is only limited by imagination

Other Categories
Check out what else can be fixed with our products
Stainless steel screws for fixing sandwich panels
